Cfd ansystrabajos

I want to calculate the drag in a fuselage from various wind direction and altitude

Looking for an individual to run with an idea for a new medical device and develop a model to emulate the device; then to create plans for a working prototype; and lastly develop mold for production. The ideal person has knowledge of fluid dynamics – specifically Bernoulli's principle and the Venturia effect as well as knowledge in creating software model (like Soldiworks) and prototyping. Aeronautical Engineering knowledge very helpful.

Stress analysis of 3D geometry of adhesively bonded single lap joint subjected to tensile load. With and without fillet at the joint ends. Preferably using ANSYS APDL. The plot of different types of stress are required along different lines of the model. Also a small explaination of how it was done will be needed on completion for verification purposes.

Stress analysis of 3D geometry of adhesively bonded single lap joint of FRP laminates subjected to tensile load. Preferably using ANSYS APDL. The plot of different types of stress are required along different lines of the model. Also a small explaination of it was done will be needed on completion for verification purposes.

Produce a report based on a simulation

ANSYS Crash, Impact, Backlash Test required for Honeycomb Chassis. Along with Design calculations.

I need help with the attached file.

I'll give the geometry file and I just want the simulation to be done for stress and temperature distribution in explicit dynamics in ansys. it is a basic simulation of orthogonal cutting with a single point cutting tool and a metal sheet.

I'll give the geometry file and I just want the simulation to be done for stress and temperature distribution in explicit dynamics in ansys. it is a basic simulation of orthogonal cutting with a single point cutting tool and a metal sheet.

I'll give the geometry file and I just want the simulation to be done for stress and temperature distribution in explicit dynamics in ansys. it is a basic simulation of orthogonal cutting with a single point cutting tool and a metal sheet.

in a simple orthogonal cutting, the equivalent stress and temperature distribution of the tool and work piece should be found out using ansys- explicit dynamics

I want to learn Ansys workbench modules from begining, any professional simulator will be prefired ...theory +practical(Hindi language preferred)...my budget is 100-200 rs/ lowest rate will be preferred

have a project for my manger in my company about Wind Turbine for design and development Overview of this project #1:Mechanical engineer expert for helping me in one week during this project #2:Have expert experiences for wind turbine about blades, Development mechanism #3:the major for the project provides a solution f...about Wind Turbine for design and development Overview of this project #1:Mechanical engineer expert for helping me in one week during this project #2:Have expert experiences for wind turbine about blades, Development mechanism #3:the major for the project provides a solution for easy to movable , reduce noise,etc!!! during in chat #4:Have experiences in Academic writing &perfect for programing ANSYS&MATLAB if u want don't can do this pleas don't...

design and test new prosthetic foot by ansys

i have a project for my manger in my company about Wind Turbine for design and development Overview of this project #1:Mechanical engineer expert for helping me in one week during this project #2:Have expert experiences for wind turbine about blades, Development mechanism #3:the major for the project provides a solution for easy...about Wind Turbine for design and development Overview of this project #1:Mechanical engineer expert for helping me in one week during this project #2:Have expert experiences for wind turbine about blades, Development mechanism #3:the major for the project provides a solution for easy to movable , reduce noise,etc!!! during in chat #4:Have experiences in Academic writing &perfect for programing ANSYS&MATLAB if u want don't can do this p...

Corrosion equations was prepared in c code and added some udf language in Fluent. But some mistakes or mising parts can be in it, it did not work. Can you make it work? And also you can write some corrosion equation (3-5 eq) into the code if needed. After loading into the Fulent, if it works and give true result, project will be done.

I need someone to look into FEA analysis in ansys and I can share more details

У меня есть зд модель кольца, его прочность нужно высчитать

I need someone who is well experienced in Ansys to complete a task. Once you place your bid I will send you the details. The work must be 100% your own and unique. That means you have to complete the task yourself. Copying, using google, etc... is strictly forbidden and you will not be paid for the project.

Need ansys modeling and analysis of metal matrix composites during turning

REPORT OF SEISMIC / needs work on LINPRO and ANSYS Include graphs of both LINPRO and ANSYS work [ [ [ PLEASE READ THE ATTACHMENT, IT'S CLEARLY DISCRIPE WHAT'S NEEDED ] ] ] if you think you can help with that without wasting time ,please Direct message me THANKS

To do ansys analysis and modelling of metal matrix composites during turning

We need to build the following 3CX Call Flow Designer apps for 3CX Phone system: 1. During Outbound calls performed by agent/operator, before starting the conversation IVR prompt should be played to warn other side that he is contacted by Company XYZ and the call is being recorded, after which agent is connected to customer to start conversation. 2. for telemarketing purposes - Automatic Dialer, which performs IVR surveys with predefined contact list and collects responses in the database. 3. after finishing the call to the customer, to perform IVR call to get the feedback on the completed call. rate the call from 1 to 10.

Using Ansys, TIG welding followed by mechanical load

I have completed the theoretical & computational analysis. The analysis is based on the natural frequency of free vibration calculation of aluminium beam cantilever & Fixed-Fixed support. I would like to double check on my analysis. I will provide you with my values & Ansys Workbench Files. You will need Ansys 2020 (R2) version to open the file.

this helmet contains few sensors and wire. And I want the result within 2-3 days. design using Solidworks and analysis using ANSYS fluent

need cfd and nastra simulation with result

need cfd and nastra simulation with result

Explain the CFD Result contours

simulation cylinder flow LEVEL SET METHOD LSM using large eddy simulation ============START ITERATIONS========= ntime: 1 rmax: 0.155918E-06 iter 2 ntime: 2 rmax: 0.677145E-07 iter 2 ntime: 3 rmax: 0.420393E-07 iter 2 ntime: 4 rmax: 0.352994E-07 iter 2 ntime: 5 rmax: 0.833854E-07 iter 2 ntime: 6 rmax: 0.470976E-06 iter 2 not converged!! 30 26.3763047447353 BIG RMAX!! STOP!!!!! 26.3763047447353

I need someone with the 2020 Ansys Program to design a bracket structure very simple structure and print out an ansys report with the required pictures and values from the time the parameters and design is given i will need the pdf of the ansys report generated through ansys in an hr to 1 1/2 hrs from then

You have to perform a simulation for my metal chair.

10, 12 ,14, 16 inches pipelines with insulation, are laid on seabed depth 2000 m. Inlet and outlet parameters, sewater parameter are avaliable. (take lenght 5 m)

Hi there, I have a task related to CFD - OpenFoam

Hi I have a task related to CFD - OpenFoam

Hi, I need some task to be done related to CFD Any heat pipe or tube CFD simulation using OpenFoam software to study flow characterestics like thermal properties 1. Design of the pipe using CAD 2. analysis part incase any: Ansys 3. simulation: Openfoam or if you have any idea that is also fine

Hi, I need some task to be done related to CFD Any heat pipe or tube CFD simulation using OpenFoam software to study flow characterestics like thermal properties 1. Design of the pipe using CAD 2. analysis part incase any: Ansys 3. simulation: Openfoam or if you have any idea that is also fine

Hi, I need some task to be done related to CFD Any heat pipe or tube CFD simulation using OpenFoam software to study flow characterestics like thermal properties 1. Design of the pipe using CAD 2. analysis part incase any: Ansys 3. simulation: Openfoam or if you have any idea that is also fine

I need solidworks design and ansys simulations work on project titled process analysis of grinding of laser treated ceramic material. I need modelling and simulations related to this project. this is mechanical related project.

We have the website: the problem: when typing "" in google search a Viagra selling website is shown for the URL site cfd-finite-elements.com. please fix this problem. deliverable: that the search result directs in the search for to

thermohydraulic calculation in Ansys and simulate the heat exchange under different geometric conditions

thermohydraulic calculation in Ansys and simulate the heat exchange under different geometric conditions

Need expert in ANSYS and in analytics Part 1. Two-dimensional heat sink analysis using numerical finite-difference method. Part 2. Three-dimensional heat sink analysis using analytical method and ANSYS numerical method and rest of things will share in chat

Require simulation report using ANSYS fluent

Engineer with autocad, ansys, solidwork and java skill can work with me. Please bid on my project with your application. You will be paid monthly cost. thanks

create code to capture movement on any financial asset gold stock fx and create trading script to show profit and loss into spreadsheet as past transaction . back testing

Consider a cylindrical pipe. Atmospheric air at 30 deg C is pumped through the inner side of the cylinder along its axis. T...side of the cylinder along its axis. The flow rate of air through the inner side can be taken as 2500 kg/hr and the exit temperature is 1100 deg C. The outside of the cylinder is exposed to high-temperature combustible gas, and the flow is perpendicular to the pipe axis. The high-temperature gas flow rate is 10,000 kg/hr at 1200 deg C. Calculate the heat transfer rate for this case study using Ansys Fluent model. then another model replacing cylinder with rectangle and find the heat transfer rate. then to increase heat transfer rate add fins to the body and develop another model. so basically 3 models. (dimensions: outer diameter 0.3m, inner diameter 0.25m, ...

perform a thermohydraulic calculation in Ansys and simulate the heat exchange conditions under different geometric conditions and fuel element locations.

perform a thermohydraulic calculation in Ansys and simulate the heat exchange conditions under different geometric conditions and fuel element locations.

perform a thermohydraulic calculation in Ansys and simulate the heat exchange conditions under different geometric conditions and fuel element locations.