Find Jobs
Hire Freelancers

Compressible Flow Project: Turbojet Design

$30-250 USD

Terminado
Publicado hace más de 5 años

$30-250 USD

Pagado a la entrega
I would like the tasks on the attached PDF to be completed in a clear professional manner that includes all methods, equations, and MATLAB/ Excel code (where applicable) used to arrive at final solution. Thank you. A propulsion system uses a turbojet engine. The combustion gas drives the turbine and is then accelerated to high speeds through a converging-diverging nozzle. The temperature at the exit of the combustion chamber (inlet of the turbine) is 1313 K. It is assumed that the combustion process takes place at very low Mach numbers (< 0.2), and therefore is a constant pressure process (no pressure loss). The thermodynamic processes in the compressor and in the turbine are considered isentropic (do not confuse this isentropic process with that in variable area flows) and the Mach numbers at their inlets and outlets are low. Consequently, in the calculations the thermodynamic properties in the combustion chamber, compressor, and the turbine can be considered as stagnation properties (as we described in the class). The flow in the nozzle is also assumed to be isentropic and the flow at the nozzle exit is perfectly expanded. Assume the mass flow rate of the fuel is negligible. Tasks to be completed: 1 Determine the optimal compressor pressure ratio to achieve the maximum specific thrust on the ground (temperature=293K, pressure=100kPa, and negligible flight Mach number, e.g., during take off). Determine the air mass flow rate needed to achieve a thrust of 55kN. If an afterburner is used, determine the afterburner temperature in order to achieve a thrust of 70kN. 2 If the turbine inlet temperature in Part 1 is increased to 1600 K, determine the optimal compression ratio and the specific thrust. 3 Determine the optimal compressor pressure ratio (for a turbine inlet temperature of 1313 K) to achieve the maximum specific thrust for a flight Mach number of 2.1 at 15000 m altitude, where the atmospheric temperature and pressure are 216K and 12.11kPa, respectively. You need to do calculations for several compression ratios to find the optimal value. Assume that the inlet is isentropic. 4 Design a two-dimensional inlet with three oblique shocks and one normal shock for operation at M=2.1. Minimize the stagnation pressure loss by varying the deflection angles. A good starting point is to use three identical deflection angles and find the best value. The angles can then be varied around this value to achieve the best values. For simplicity, use the (constant) properties of air in all calculations. The specific thrust for a perfectly expanded nozzle can be calculated as R/m=ue-ui. Important: Obtain ue using the pressure and temperature just upstream of the nozzle. Perform step-by-step calculations of the temperature and pressure (from the inlet to the compressor, combustion chamber, turbine, and nozzle). Do NOT use the efficiency formula. keywords: aerospace engineering, mechanical engineering, aerodynamics, Matlab
ID del proyecto: 18253950

Información sobre el proyecto

3 propuestas
Proyecto remoto
Activo hace 5 años

¿Buscas ganar dinero?

Beneficios de presentar ofertas en Freelancer

Fija tu plazo y presupuesto
Cobra por tu trabajo
Describe tu propuesta
Es gratis registrarse y presentar ofertas en los trabajos
Adjudicado a:
Avatar del usuario
Hello I'm Mohamed Saeed . aerospace engineer and master candidate in gas turbine engine. I'm expert in jet engine design and simulation staring from turbojet, low bypass ratio turbofan, high bypass ratio turbofan. I have checked your job description in details and ready to help you. I'm able to solve the performance cycle starting from diffuser , compressor, combustion chamber, turbine, afterburner and nozzle if chocked or not. best regards
$111 USD en 1 día
4,8 (58 comentarios)
6,0
6,0
3 freelancers están ofertando un promedio de $97 USD por este trabajo
Avatar del usuario
Hello, dear! I am interested in your project. I have extensive experience in Matlab. As a developer with rich experience, I am confident about your project. I will provide perfect results in a short time. If you want to work with me, please feel free to contact me. Thanks.
$150 USD en 3 días
5,0 (41 comentarios)
6,1
6,1
Avatar del usuario
I am a Mechanical Engineer with a masters degree in Aerospace engineering. I have experience in Mechatronic, FEA, Hydraulic actuator, Matlab,3D Modelling, CAD/CAM, AUTOCAD, CFD, NX Nastran, CATIA, Fluent ANSYS, Graphic Design, Product Design, Solidworks and expertise in simulation-based numerical optimization. I believe I am a good fit to complete your project. Once you share the project, I will have a look & confirm if I can do it. I’m honest, creative and a unique person to carry out your tasks given to me. Leaving your project on our hand is a privileged; we'll make sure that the project is done in a perfect way and do our best until you satisfied. I would love to discuss this project with you and meet your exact requirements. I am confident I can provide you with top notch materials that will fit your needs. I'm proud my work on being professional, of the highest quality and always delivered on time. you can hire me directly through this link https://www.freelancer.com/u/olaideejiwole
$30 USD en 1 día
4,8 (54 comentarios)
6,1
6,1

Sobre este cliente

Bandera de UNITED STATES
Greenville, United States
5,0
2
Forma de pago verificada
Miembro desde abr 3, 2015

Verificación del cliente

¡Gracias! Te hemos enviado un enlace para reclamar tu crédito gratuito.
Algo salió mal al enviar tu correo electrónico. Por favor, intenta de nuevo.
Usuarios registrados Total de empleos publicados
Freelancer ® is a registered Trademark of Freelancer Technology Pty Limited (ACN 142 189 759)
Copyright © 2024 Freelancer Technology Pty Limited (ACN 142 189 759)
Cargando visualización previa
Permiso concedido para Geolocalización.
Tu sesión de acceso ha expirado y has sido desconectado. Por favor, inica sesión nuevamente.