Arduino library and example programs to control the Si5338 clock chip.

FREELANCER RECOMMENDED ------------------------------------------------------ Can help... I am an Expert... Lets Start! Please start a Discussion with me and we can get started from there... Please check the past projects I have handled and check my reviews for what employers have to say about my work... Can start right now...

I have significant experience in low level (even bit banging) I2C and Sensirion protocol in C as well as low level (dsPIC33) I2C experience.

Interested to do the job **************** *********************** ********************************************

Hello Sir. I am electronics engineer and have experience in designing Arduino based system. I would like to do this for you. let me know if you are interested. kindly keep in mind that I don't have this IC right now and it will take some time to order it online and start work. thanks

Hello, I would like to express my interest in working with you on your project. I have strong experience in avr microcontroller programming and i2c bus interface. Also I'm very skilled in producing well documented, well tested and portable code which you will need in your library. Please have a look at my profile and contact me if you fell comfortable working with me. Also please consider that the bid's details are negotiable .if you have another terms you prefer to work with, please mention them. best regards, MG

dear Sir i can do this project. I can assure you that if you work with me once, you will always work with me for these kind of projects.

Hi, Can you please share your Eval-Board or Schematics. And which Arduino board you are planning to use. About us: We have 10 years of experience in Product development. Micro-controllers we have worked on PIC, STM32, PSOC and AVR. Development kits and instruments available for testing purpose. For PCB designs we use KICAD. C#, LABVIEW, Python for GUI, Controlling or Datalogging purpose. Thanks and Regards, Santosh

I am an Electronics and Electrical Design Engineer with the areas of expertise in Embedded System, product prototyping, PCB design and layout and firmware development for systems. Experience: I have worked with different topologies for DC-DC, AC-DC, DC-AC converters. Completed a lot of projects based on MCU - ARM - STM32, AVR, ESP8266, PIC, ARDUINO. I have knowledge and working experience with interfaces - RS-485/232/422, Wi-Fi, Bluetooth, SPI, I2C etc. a lot of sensors, peripheral ICs. Software proficiency: • AUTOCAD • MATLAB • PROTEUS Design Suite • ARDUINO • ALTIUM Designer • KICAD • ESP8266 Gaining your trust is vital for me because I want to make friends on freelancer. I am available 24/7 and can start your project as soon as possible. If interested please contact me to talk in more detail about the project and define our milestones.

Respected Sir,,,, Its me imad ud din, An electronics engineer, have completed about 200+ projects of electronics and electrical. e.g 1. Digital Stethoscope using arduino 2. Door Lock System using PIC and Arduino. 3. Fully automized Car parking and collection system. 4. Image Recognition using Viola Jones Algorithm 5. Servo Motor Control Circuit using Arduino and MATLAB. 6. Grid Tied Inverter using ATMEGA controller. You will find an extreme friendly and brotherhood relationship.

A proposal has not yet been provided

I'm an italian electronic engineer with more than 14 years of work experience. I work as HW designer; FW and SW developer. As HW designer, I work in Altium, KiCad and Orcad and I have experience in development single MCU (Microchip PIC and ARM Cortex) boards with several digital I/O (GPIO, UART, SPI, I2C, PWM,....) and some analog I/O. I design complete board: power section, MCU section, peripheral section,.... I design also boards with battery power; so I have experience in low power PCB design. I have also experience in commercial boards (Arduino, Raspberry, Beaglebone,...) shields design. I have also experience in bluetooth (both 2.0 and 4.0) PCB design. As FW developer, usually I work in C for Microchip PIC (MPLAB X + XC compilers) and Eclipse + GNU ARM for different ARM Cortex M3/M4 manufacturers (but I'm ready to swith to new frameworks). I work both in single task and multi task environment (FreeRTOS). I write code both for low level driver (GPIO, UART, SPI, I2C, PWM....) management and for high level/final application. I work also in "C code" commercial boards Arduino/ESP8266 and Linux embedded commercial boards (Raspberry and Beaglebone). I have also experience in bluetooth (both 2.0 and 4.0) programming. As SW developer, I work in .NET, Java, and lot of others programming languages. Mainly I work for Windows O.S., but I have experience in Linux development too. Also I have experience in Android App development with Java (Eclipse + Android SDK + Java).