Tilingtrabajos

I’m ready to have a bathroom in Adelaide professionally tiled with quality ceramic tiles. The room is stripped, clean, and measurements are on hand; the next step is a precise installation that will stand up to daily use and our local climate. I have alr...joints and fixtures • Removal of leftover debris and a final clean so the bathroom is ready for fittings Acceptance criteria • Tiles sit level with uniform grout lines (±2 mm tolerance) • No lipping or hollow spots when tapped • Waterproofing certification supplied (where membrane is applied) • Site left clean and all waste disposed of responsibly If you are experienced with bathroom tiling in South Australia, familiar with local standards, and can start soon, let’s ta...

...depict ancient manufactured Forerunner infrastructure partially reclaimed by nature, with approximately 40–45% exposed hexagonal surfaces, 30–35% earth or mud and 20–25% low vegetation. These materials should overlap organically throughout the sheet, providing varied, convincing compositions within small sampling areas while retaining broader, relatively level spaces for large models. Seamless tiling is unnecessary. The defining requirement is that every intact hexagonal pillar uses the same nominal 10 mm across-flats footprint and rotational orientation: corresponding flat sides must remain parallel across all clusters. Heights, burial, weathering and small geometric indents may vary, and soil-separated clusters may shift position, but intact modules must neve...

ABOUT THE COMPANY Centrum Bad (Kaps Consulting ApS) is a Danish startup specializing in complex bathroom renovation projects inside apartment buildings - work that requires technical design, engineering, and formal approval from housing associations and sometimes municipal authorities, not just tiling and plumbing. The team is small but highly competent, with strong relationships across the entire supply chain. Budget is a real factor: this is a lean, sharp startup, not a corporate account, and we expect the same discipline from partners we hire. WHAT ALREADY EXISTS The site's content, structure, and visual identity are fully finished and live as a working reference, built in Webflow at a staging URL () - not yet on a custom domain. All five main pages have real, finished

...orthographic top-down, a plan view like a drone directly overhead. No perspective, no visible walls, no isometric or 2.5D tilt. A round fuel tank is drawn as a circle. Height is suggested with a consistent soft shadow, not with geometry. The four assets are a fire station, a fuel farm, a short stay car park, and a terminal roof tileset. The tileset is the main piece of work and needs proper seamless tiling — edges, corners, diagonals and triangles for the outline, plus a set of interior tiles (roof membrane, plant and ducting, vents, rooflights, solar) that mix without an obvious pattern. Everything is PNG with transparency on a square grid, 256x256 per tile, drawn north-up in one orientation only — the engine rotates and scales. If the style works there&...

I’m setting up a small online shop focused on just five tiling-levelling products and I need a clean, modern, minimalist website to match. The site should feel light and uncluttered yet make it effortless for customers across Australia to select a product, read all the details, checkout and pay. Core requirements • Design aesthetic: modern and minimalist, with plenty of white space and straightforward navigation. • Catalogue: only five products, each with a dedicated page that includes a zoomable image gallery, a detailed description and space for customer reviews. • Payments: integrate credit/debit card processing, PayPal and bank-transfer options so buyers can choose what suits them. • Mobile responsiveness and fast loading are essential. I&rsqu...

I need an experienced Tile and Flooring installer to remove 700 ft.² of ceramic tile flooring. Prep the floor for 3500 ft.² of snap together waterproof wood flooring to be laid. This is a commercial building in Huntsville Alabama, Once the surface is ready, I want the new wood flooring installed with clean transitions at doorways and edges. All tools, spacers, saws, and setting materials should be provided by you, along with disposal of any debris created during the job. When the last board is in place, the floor should cure properly and be ready for traffic without slippage or hollow spots. Please include an estimated timeline and a brief note on similar large-format projects you have recently completed so I can gauge fit and quality.

...Complete layout overhaul including studwork, insulation, acoustic fire boarding, and ceiling grids. Full M&E Sub-Contract Packages: Distribution boards, rewiring, lighting, heating, FCUs, fire dampers, ducting, and public health installations. Fit-Out & Joinery: High-spec installation of kitchens, bathrooms, fire doors, skirting, and tailored storage solutions. Finishes & External Works: Wall/floor tiling, premium LVT/screed flooring, complete internal decoration, and secondary glazing. Preliminaries & Logistics: Comprehensive site setup, welfare facilities, waste management/skips, and urban site logistics (ULEZ/parking coordination). Required Freelancer Deliverables 1. to fill in the costs of the Full Bill of Quantities (BoQ) 2. Schedule of Works: Comprehens...

The goal is a repeatable script-based workflow: feed in a texture (PNG, JPG or directly from a generative model), target one or more prisms, and receive a mapped result ready for rendering , using Blender’s Python API The core of the job is the tiling logic—seamless repetition, correct scaling, and clean UV placement—so that the texture looks natural on every face of the geometry I select.

The goal is a repeatable script-based workflow: feed in a texture (PNG, JPG or directly from a generative model), target one or more prisms, and receive a mapped result ready for rendering , using Blender’s Python API The core of the job is the tiling logic—seamless repetition, correct scaling, and clean UV placement—so that the texture looks natural on every face of the geometry I select.

CRITICAL AMENDMENT: THIS IS NOT A REPEATING WALLPAPER PATTERN. DO NOT MAKE TILING ARTWORK. Project: Solemn Academic Crest & Memorial Vector Emblem for a Late Professor Style: Modern (Minimalist Geometric & Conceptual Art) Application: To be permanently engraved on a dark granite tombstone via sandblast etching. Core Concept: An artist's paintbrush and a scientific drafting divider / mathematical caliper (two-legged technical style) symmetrically crossed in an elegant 'X' shape, subtly surrounded by 3 to 5 minimalist swirling starbursts (cosmic space background theme). It must be a single, standalone, centralized emblem / academic crest. Strict Technical Requirements: 1. Style: Single center-aligned crest. Clean, solid, and bold black lines on a solid white ...

...Extraction: Separate the original room shadows and light reflections into an independent layer, configured with the "Multiply" blend mode. This ensures that new textures rendered underneath look hyper-realistic and sit naturally behind furniture and ambient shadows. 3. Seamless Texture Creation: Take [ 20 samples] of our high-res product images and process them into perfect Seamless Textures (tiling patterns) that repeat without any visible seams or geometric distortion. Requirements & Output: * Deliverables must be in fully organized, named, and open-source PSD files, along with exported transparent PNGs for the alpha masks. * A solid portfolio demonstrating prior experience in professional image masking, layer isolating, or product editing is required....

I have a floor plan and an example image that captures the exact level of realism I need. Your task is to create a highly detailed 3D visualiza...camera angles. 2. Source file in your preferred 3D software (e.g., 3ds Max, Blender, SketchUp + V-Ray/Corona) with textures, materials, and lighting intact. 3. A short material and lighting summary so I can replicate tweaks later if needed. Acceptance criteria • Proportions must match the provided floor plan exactly. • Textures, reflections, and shadows should appear natural—no visible tiling or noise. • Final images delivered in 4K PNG or TIFF, ready for client presentation. I’m happy to answer questions about furniture references or accessory inspirations. Looking forward to seeing the room come t...

...Real-time leaderboards showing top & bottom performers, visit counts, conversion ratios and overall app usage. The finished build must run smoothly on both platforms, respect native location-permission policies, and use Google Maps (or Places) APIs for the data pull and review ranking logic. Clean UI/UX, secure login and cloud sync are expected. Acceptance will be based on: 1. Accurate map tiling down to small-block level with pins and colour logic. 2. Live location updating ≤5 sec latency while on cellular or Wi-Fi. 3. Reliable write-back of status flags even when the device is briefly offline. 4. Role-based dashboards reflecting live data without manual refresh. Code repo, brief setup docs and a test build for iOS & Android are the final deliverables.....

...Identity — Design Brief for Centrum Bad About the company Centrum Bad (legal entity: Kaps Consulting ApS, CVR 46402340) is a Danish startup specializing in complex bathroom renovation projects in apartment buildings (etageejendomme) — the kind that require technical design, engineering, and formal approval from housing associations (boligforeninger) and sometimes municipal authorities, not just tiling and plumbing. That approval process is where most competitors' projects stall; handling it smoothly is Centrum Bad's core differentiator. The team is small but highly competent, with strong relationships across the entire supply chain (fast access to quality materials at competitive prices). The brand should read as confident and capable — a company tha...

...walls and a proper door—to give the toilet its own private zone. The enclosure needs an integrated ventilation fan, and the finishes throughout the room should lean on elegant marble surfaces that pair well with the current fixtures. Because the plumbing will not be relocated, the plan has to make clever use of the existing supply and drain points. I’m open to minor framing adjustments and re-tiling, but nothing that requires breaking concrete or rerouting pipes. Deliverables • Scaled floor plan and elevations showing the new water-closet layout • At least two 3D perspectives or renderings illustrating the traditional aesthetic and marble finish scheme • Construction notes highlighting wall thickness, door swing, and any code-compliant clearances ...

I’m producing a short 15-second, full-HD animation that showcases key ...frame for thumbnail/cover. • Editable project files (Maya/Blender/3ds Max, After Effects, or your preferred 3D package plus compositing file). Acceptance criteria 1. All three requested infrastructure elements—buildings, roads, bridges—are clearly visible. 2. Industrial backdrop reads immediately without looking post-apocalyptic or overly clean. 3. No noticeable geometry flicker, texture tiling, or lighting noise in the final render. 4. File delivered on time and opens without missing assets. If you have recent examples of similar realistic environment animations, linking them will speed up approval. Let me know which software you’ll use and any questions you have ab...

I run a busy commercial flooring company in Australia and need a committed estimator who can take full ownership of our quoting pipeline. All work is commercial—no residential or industrial jobs—and the typical packages you will price include carpet tiles, vinyl flooring, tiling, waterproofing, and sand & cement screed. The role is 100 % remote; drawings, finishes schedules, and scope notes will be supplied electronically, and I’ll rely on you to return clean, fully costed estimates without the need for site visits. Core expectations • Produce precise quantity take-offs directly from digital plans • Build complete cost estimates that break out materials, labour, prelims, and margins • Flag clarifications or RFIs promptly so our bids sta...

...ends with a final exterior sweep Render quality should hold up to 4K display, with natural lighting, soft shadows and realistic reflections. Native files (e.g., 3ds Max, SketchUp, Revit, Blender) plus exported formats and raw animation footage are required so I can make future tweaks if needed. Acceptance criteria: models align precisely with supplied dimensions, textures are free of tiling artefacts, and the final walkthrough plays without stutters on a standard media player. I’m happy to review WIP drafts at agreed milestones, provide quick feedback and keep the turnaround efficient....

I need a small outdoor area—just under 100 sq ft—finished with natural-stone tiles. The surface is still raw, so the first step will be proper preparation: ensuring a level, well-compacted base with suitable waterproofing and mortar bed for exterior conditions. Once the base is ready, set and align the stone tiles, make any precise cuts, apply outdoor-grade thin-set and grout, and leave clean, even joints throughout. All waste material and debris should be cleared away on completion so the space is ready for immediate use. Deliverables • Prepared substrate, fully cured and level • Natural-stone tiles securely installed and grouted • Final clean-down and disposal of off-cuts/debris Workmanship will be checked for level, adhesion, straight joints, an...

...correct heights, door and window openings placed, floor and ceiling levels defined—so I can visualise the space and base my budget on solid quantities. Once the model is ready, I want a detailed bill of quantities and cost estimate that covers every trade involved in bringing the unit to a turnkey finish: plastering, floor screed and levelling, electrical rough-in and fixtures, plumbing runs, tiling, painting, cabinetry, and any final decorative work. Break the numbers down by area and trade so I can drop them straight into my estimating template. Deliverables • SketchUp (.skp) file, layered and grouped for structure, services, and finishes • PDF/Excel take-off tables with measured quantities per trade • Cost estimate summarising labour and materials,...

...print-ready PDFs, and will review progress over two scheduled revision rounds. Deliverables (not all projects will require all level of plans but generally should cover the following): • Full home layout floor plans • Detailed kitchen and living-space drawings and cabinet design • Bedroom and bathroom layouts with fixture notes - with detailed elevations showing fixture and fittings locations and tiling layouts • Complete electrical plans compliant with AS3000 • Building sections with construction call-outs • Exploded axonometric details of container junctions and modular connections All sheets must be dimensioned, fully annotated, and referenced to the NCC/BCA where required. Experience with container or modular residential work is highly va...

I have a set of texture images that need to be transformed in Adobe Photoshop into perfectly seamless, all-direction tiling patterns. The final look must be distinctly geometric, because these tiles will serve as repeatable backgrounds and UI accents throughout a website and companion app. You’ll receive the original high-resolution source files as soon as we start. Your role is to align, clean up, and edit each image so there are absolutely no visible seams when the pattern is repeated horizontally, vertically, or diagonally. Color, tone, and scale should stay consistent across the edges to avoid any “grid” effect once implemented in CSS or SVG backgrounds. Optimum output dimensions are welcome—think web-friendly file sizes without sacrificing sharpness o...

...100 residential units per floor 5,600 Unit Twins Hallways Staircases and floor-to-floor segments Passenger and service elevator landings Utility and restricted rooms Vertical risers and shafts Shared building systems Every unit and common space must have a permanent ID. The viewer must never load the complete high-rise model at full detail. It must use progressive loading, spatial tiling, caching and levels of detail. Typical loading behaviour: Open property: load site and low-detail building exterior. Select building: load building structure and summary information. Select floor: load only that floor and its operational records. Select unit: load the detailed Unit Twin. Select common area: load only the selected hallway, landing, staircase segment or utili...

I need a series of hi...accurate modeling are still important, but texture fidelity is my primary concern. Technical notes • Native files in .blend or .uproject, plus exported 4K PNGs/JPEGs. • Physically based materials only; no baked-in lighting. • Color profile sRGB, 300 DPI, transparent or solid background as needed for web. Acceptance criteria 1. Visual realism comparable to the reference link. 2. No visible tiling, stretching, or noise on textures. 3. Consistent real-world scale—cabinet heights, countertop depths, etc. 4. Final images load cleanly on desktop and mobile without artifacts. Let me know your preferred software, approximate turnaround time, and any previous kitchen or product renders you can share. I’m ready to start as so...

I am starting a residential tiling and grouting business in Perth, WA. I provide services including regrouting, sealant/silicone work, waterproofing, small bathroom/laundry/kitchen renovation work, and tile repair. I am specifically looking for someone who can generate qualified leads for regrouting jobs and ensure these leads are converted into confirmed appointments. My main goal is to connect with homeowners in Perth who are genuinely interested in regrouting their tiles. Your job will include: • Performing cold calls to potential residential customers in Perth • Qualifying leads carefully to confirm their interest in tile regrouting • Confirming their details including name, suburb, phone number, job specifics, and preferred contact time • Setting up a co...

...definitely need are sturdy grab bars positioned beside the toilet and inside the shower, plus non-slip flooring throughout the room (tiles or sheet vinyl are both fine as long as the slip-rating is high). Please allow for gentle floor grading into the new shower pan so no lip is required. You’ll handle demolition, plumbing relocation if the drain needs moving, waterproof membrane installation, tiling or flooring, and finishing carpentry around the doorway once the sill is gone. Include all fixtures and fittings installation, caulking, and final cleanup. Deliverables • Site-ready bathroom with door threshold removed and level transition • Fully waterproofed walk-in shower with correct fall and drain • Installed grab bars and non-slip floor surface • All...

...the value of remaining works, control variations and provide commercial support through to completion. 4. Architect / Designer Scope Required • Carry out a site visit and review the current construction status. • Prepare or update existing floor plans, elevations and relevant sections based on the current site condition. • Prepare coordinated bathroom layouts, including sanitaryware positions, tiling intent, lighting positions and ventilation requirements. • Prepare kitchen design layouts, including appliance positions, services requirements, lighting and ventilation requirements. • Prepare stair design information, including layout, dimensions, compliance considerations and coordination with surrounding structure. • Coordinate electrical layouts, in...

...high-resolution renders (minimum 4K) from multiple eye-level viewpoints per room; include one overall interior walkthrough camera if possible so I can create a short fly-through later. • Native scene file (e.g., 3ds Max, SketchUp, Blender) plus exported FBX/OBJ for my archive. Acceptance criteria The model must match the provided plans within a few centimetres, surfaces should be free of visible tiling or noise, and lighting should be balanced—no burnt highlights or crushed shadows. I will sign off after two review rounds: first pass clay model for layout, second pass fully textured preview, then final delivery. Please let me know which software and render engine (V-Ray, sketchup, Cycles, Lumion, etc.) you plan to use and share a portfolio link showing comparable...

...Job: Capture raw videos and high-resolution photos of tile grouting lines on active or recently tiled construction sites. - The Catch: To perfectly replicate our robot's perspective, your camera must be mounted at a specific, fixed height (exact measurements and setup guidelines will be provided). - Requirements: You must have verified, legal access to a construction site with ongoing or recent tiling work. Please confirm this access in your proposal. Task 2: Computer Vision Data Labeling - The Job: Accurately label and annotate the tile grout lines from the videos and images collected. - Requirements: Needs to know how to use a computer. - Experience: Prior experience with standard computer vision annotation platforms and exporting to standard formats (JSON) is preferred. ...

...scene in Unreal Engine and now I need a fresh set of expert eyes to critique only the textures and materials. Lighting, shadows, and mesh work are in place for now; the focus of this pass is surface realism, fine-grained detail, and faithful, consistent colour. Here’s what I’m after: • A concise written review (bullet points or annotated screenshots) pinpointing where realism breaks down—think tiling, roughness values, normal map strength, or mismatched albedo. • Recommendations for achieving better colour accuracy and cross-asset consistency, including any LUT, material instance, or post-process tweaks you’d suggest. • If you notice any obvious performance pitfalls tied to texture size or material complexity, flag them, but depth opt...

I’m launching a new clothing line and need original repeat-ready patterns that translate beautifully to fabric. My goal is to build a small library of seamless prints that can be used for a small collection of pyjamas to start my business without obvious tiling or loss of detail. What I’ll give you • Garment sketches, mood boards and reference swatches so you understand placement, scale and the overall vibe of the collection. . What I’m asking for • Three fully developed, seamless repeat patterns in high-resolution layered files (PSD, AI or vector PDF are all fine) plus flattened TIFFs ready for the printer. • Colour files in both RGB for preview and the required CMYK or Pantone values for production. • Clear documentation of the r...

...project—bathrooms, kitchens, and laundry rooms. The base geometry is already in place; what I’m missing are the construction-ready sheets that show exactly how each space is to be built. Scope of work • Use the supplied Archicad/DWG files as the starting point. • Produce detailed plans, reflected ceilings, elevations, sections and enlarged details for all wet areas. • Include dimensions, set-outs for tiling and cabinetry, waterproofing build-ups, fixture and fitting locations, electrical and plumbing rough-ins, material call-outs and any necessary schedules. • Layering, line-weights and annotation style must follow the specific standards I will describe in writing (they reflect local code plus some office conventions). Deliverables 1. P...

...commented code so I can swap out data or adjust styling later without diving deep into the API docs. Accuracy of the overlay is critical; the layer must align perfectly with standard Google satellite and street basemaps. If you normally use tools such as QGIS, Mapbox Studio, GDAL, or topojson to prepare data before pushing it to Google Maps, please let me know—anything that streamlines reprojection or tiling is welcome. Once the interactive page is running smoothly in a browser, the job is done....

I’m upgrading the garden steps and the short front pathway with slip-resistant porcelain tiles laid in a precise grid pattern. The finish needs to be a clean, straight edge that sits flush with the lawn and adjoining brickwork. Your role covers everything from surface preparation to the final clean-up. That includes establishing the correct falls for drainage, setting a solid base that won’t shift with temperature changes, cutting the porcelain accurately around risers and edges, and applying outdoor-grade grout and sealant so the joints stay tight through the seasons. Deliverables • Substrate prepared and levelled for exterior porcelain • Porcelain tiles installed on steps and pathway in grid layout • Straight edge border finished neatly all around &bu...

...and any extra notes you need; you’ll translate that into a clean, printable pattern package that a leatherworker can take straight to the cutting table. Deliverables • Full-size digital patterns for every panel, including gussets, pockets, straps and reinforcements • Clearly marked seam allowances, grain lines, rivet/hardware positions and stitch guides • Ready-to-print PDF sheets (A4/Letter tiling is fine) plus the original editable file (AI, DXF or similar) • A brief assembly guide or call-out sheet so the maker understands the build order and construction tips Acceptance criteria: printed test pieces must align within 2 mm tolerance when assembled; all notches, punch holes and hardware marks match the supplied reference dimensions. If you hav...

Job Title: Tile Layout, Cutting Plan & Quantity Takeoff from DWG (Multiple Rooms) Job Description: I am looking for a CAD specialist / drafting professional with experience in tile layout design and construction detailing. The task involves creating detailed tile layouts based on DWG files for multiple rooms. Scope of Work: Create accurate tile layout drawings for each room based on DWG plans Include grout lines (seams) and 10 mm aluminum profiles where specified Design detailed tile cutting plans (showing all cut tiles and their positions) Calculate exact quantity of: Full tiles Cut tiles Total consumption per room Prepare a clean and readable PDF output for each room Start with room 3105 as a test sample before proceeding to other rooms Important Notes: Some rooms include two tile ty...

... The immediate scope covers three areas that overlap tightly: • Sprite production – characters, enemies, props, UI elements and their frame-by-frame animations, delivered as neatly organised sprite sheets (PNG) with accompanying JSON or XML frame data if your pipeline exports it. • Tileset design – terrain, structures and decorative elements at a consistent pixel density, ready for seamless tiling. • Level mapping – assemble the tiles into playable, engine-ready maps (Tiled TMX or an equivalent format) and populate them with collision and spawn metadata. Artwork should stay true to classic pixel aesthetics: clear silhouettes, restricted palettes and animation that reads well on small mobile screens without losing charm on a desktop monitor. ...

I have several models in .glb format that need a quality...start from the original .glb files (no other formats are available) and return updated .glb versions ready for real-time use. Feel free to move the assets through Blender, Substance Painter, or any comparable tools as long as the final export keeps the original scene scale and hierarchy intact. What I will consider a successful delivery: • Visually improved, PBR-ready textures with no obvious tiling or stretching • Optimised geometry that preserves silhouette but reduces unnecessary faces • Final .glb files that load error-free in standard viewers and engines If you need any quick approvals along the way—say, on a new material style or a topology change—just send a low-res preview, and I&rsqu...

The bathroom in my home needs a new stud wall built exactly to the CAD drawings and measurements I will hand over. All timber studs, plasterboard sheets, screws and fixings are already on-site; what I’m missing is a skilled builder who can read the plans, cut accurately and assemble the frame so everything is plumb, square and ready for tiling. The room itself is cleared and accessible even though we’re still living in the property. There are no existing plumbing or electrical runs in the way, which should make the job straightforward. I’d like the work to kick off within the next couple of weeks so we can then bring in our plumber. Deliverables • Frame erected to CAD dimensions, including door opening and any noggins shown on the drawings • Plaste...

I have an architectural drawing in DVG format and I want a complete tiling plan produced from it. The space will be laid in a herringbone pattern, so I need you to translate the drawing into a clear, scaled layout that shows every tile position and all cut pieces. Your work should cover: • A dimensioned layout plan in herringbone, referenced to the room’s datum lines. • A cutting schedule that labels each cut tile on the plan and states its exact size and angle. • A tile take-off summarising the total number of full tiles, cut tiles and wastage allowance, broken down by tile type or colour if more than one is used. Please use CAD software that can read my DVG file (AutoCAD, BricsCAD or similar) and return the final drawing in both the native format a...

I am commissioning a full set of pictorial layouts and photorealistic 3D renders for a new hospital fit-out. All seven flooring and tiling zones carry equal priority, so the workflow must cover them in tandem: • Operation Theatre flooring • Patient Room flooring • Ward Corridor flooring • Common Corridor flooring • Vitrified floor zones • Ceramic glazed wall-tile zones • Ceramic matt floor-tile zones For every zone I will supply the architectural plans and exact measurements. Your task is to translate those documents into: 1. Scaled, annotated layout drawings that spell out tile sizes, joint lines, patterns, and any cut pieces. 2. High-resolution 3D views that let the clinical team picture the final result before installation. I...

I need detailed tile plans and elevations for a bathroom project. The plans should include material and installation notations. Requirements: - Tile plans and elevations - Materials: ceramic, porcelain, natural stone - Surfaces: walls, floors, shower area Ideal Skills and Experience: - Proficiency in creating tile layouts - Experience ...plans should include material and installation notations. Requirements: - Tile plans and elevations - Materials: ceramic, porcelain, natural stone - Surfaces: walls, floors, shower area Ideal Skills and Experience: - Proficiency in creating tile layouts - Experience with ceramic, porcelain, and natural stone tiles - Attention to detail and accuracy in notations - Knowledge of bathroom design and tiling requirements Please provide samples of sim...

I’m developing a series of modern, decorative wall panels and curtain-like d...perfect; as long as the output runs error-free through typical slicers (Cura, Simplify3D) I’m happy. Deliverables • Editable parametric model with key parameters clearly labeled • Print-ready files for at least three unique panel/curtain motifs • Brief PDF showing overall concept, module tiling logic, and suggested print settings Acceptance criteria – All meshes pass manifold checks and require no post-repair. – Lattice thickness respects 3 mm minimum for composite extrusion. – Tiling tolerances ±0.3 mm so adjoining parts snap or tongue-and-groove cleanly. If your portfolio shows comparable large-format, composite prints or intric...

I have a multi-page PDF that shows the entire floor plan of an office. I need that plan recreated in Godot as a clean, layered 2D map I can import straight into my project. Every room and detail visible in the PDF—reception, conference room, break room, plus any additional spaces on the drawing—must be reproduced...place and ready to connect Acceptance criteria • Visual match to the provided PDF across every page • Correct layering and node structure, easily editable • Clickable areas trigger a test signal without errors when run in Godot Once I confirm accuracy and interactivity, the job is done. Feel free to use any efficient workflow—importing the PDF as a reference texture, vector tracing, or tiling—so long as the final result i...

I need a set of polished, photo-realistic renders of a mod...sunny afternoon shot and a warm sunset shot. • Fine-tune camera angles that highlight the entry, driveway, and backyard terrace. • Export high-resolution stills (minimum 4K) plus the .LS project file so I can make future tweaks. Acceptance criteria ✓ Two final hero images (day & dusk) delivered in PNG or TIFF at 3840×2160. ✓ Consistent material realism—no texture stretching or obvious tiling. ✓ Balanced composition with natural shadows; no blown-out highlights. ✓ All source files, textures, and the editable Lumion scene handed over on completion. If you have a Lumion 12 (or newer) workflow that speeds up foliage scattering and global illumination, let me know—turnaround within ...

I need a skilled tradesperson to waterproof and tile my bathroom, ensuite, and laundry. The job includes the shower area, floor, and walls. Requirements: - Experience with waterproofing in wet areas - Expertise in tiling, specifically with ceramic tiles - Attention to detail and quality workmanship - Ability to work within budget and meet deadlines Ideal Skills: - Plumbing knowledge (a plus) - Previous experience with similar projects - Relevant certifications in waterproofing and tiling Please provide examples of past work and any relevant qualifications.

...and DiT. Core Requirements: Target Model: DOVE (Repository: ) Acceleration Target: 1.5x - 1.8x end-to-end inference speedup. Hardware Baseline: The speedup must be achieved and evaluated on a high-end NVIDIA GPU with 40GB+ VRAM (specifically targeting NVIDIA L40S, H100, or equivalent). Testing Condition: The inference speed MUST be measured under the "no tiling" setting. Quality Metrics Constraints: Image Quality Assessment (IQA) metrics and Temporal metrics must NOT decrease compared to the original DOVE baseline. PSNR and SSIM are allowed to drop, but the degradation must strictly not exceed 8%. Tech Stack: Native PyTorch. Current Progress: We already have a preliminary working version implemented with Token Merging. This can be provided to the

...spot opens on a cartoon or AI-generated Hispanic woman who energetically delivers one line in English with a light Hispanic accent: “Does your man work in construction and does side jobs? Sign him up for a free account on , find jobs close by, and get those bills paid today!” While she speaks, I want quick-cut background footage of workers in action—think framing, drywall, tiling, and other home-improvement moments—so viewers instantly connect the message to real job sites. The voice should feel energetic and enthusiastic, matching the upbeat TikTok style. Key points • Format: 9:16, 1080 × 1920, 15–20 sec. • Character: original cartoon or AI-generated Hispanic female, lips synced to the line. • Visuals: dynamic worker-in-a...

...step-by-step installation guidance Use engaging visuals, motion, and possibly 3D or enhanced editing to make the product stand out Produce content suitable for online retail (Amazon, Shopify, website product pages, ads, etc.) Key focus for this project: Demonstrate how the modular wall panels (tile-format system) quickly and seamlessly interlock Highlight ease of installation vs. traditional tiling Showcase material quality, finish, and modern design Create a video that feels both aspirational (sales-driven) and practical (instructional) We will provide product images and references. Experience in product visualization, home improvement, or construction-related video content is a strong asset. If you can create videos that not only explain a product but also sell it effective...

I’m working with a fabric print that currently measures 240 mm × 130 mm and need it expanded to a final artboard of 2500 mm × 929 mm. Instead of a simple scale-up, the design must be tiled so the pattern flows seamlessly across the new dimensions—no visible repeats or mismatched joins....for large-format printing. Deliverables • One print-ready file at 2500 mm × 929 mm (preferred formats: layered PSD, AI, or high-quality TIFF) • Seamless pattern work verified at 100 % zoom with no hard edges or artefacts I’ll review by placing the file into a 2500 mm × 929 mm template and zooming in for any seams, so please double-check before sending. If you’re comfortable with pattern tiling in Photoshop or Illustrator and can turn ...